Gas Suppression System

Product Details:

As a quality focused firm, we are engaged in offering a high quality range of FM200 Fire Suppression System.

Fire Project has expertise in SITC of FM200-Fire Suppression System along with its component. Fire suppression here it called as FM200 gas suppression systems are commonly used in:

• DATA Centres
• Comms Rooms
• Telecommunication facilities
• UPS Rooms
• Medical facilities
• FM200 is waterless, gas based suppression system, which discharge into the risk within 10 seconds depending upon configuration for discharge
• FM200 is also known as HFC227ea suppresses fire immediately
• HFC227ea (formed from elements hydrogen, fluorine and carbon) remove the elements of fire triangle (Oxygen, Heat and Fuel)
• FM200 gas is transparent, colourless and safe for human but may cause frostbite if liquid discharge or escaping vapour contacts the skin
• Fire Projects has done sevaral designing to installation of FM200 with after sales service
• Based on infrastructure and requirement we give our expert opinion to prepare BOQ

Complete solution consists following components and accessories required for installation:

FM200 storage components:

• Cylinder assembly for FM200 chemical agent gas
• Cylinder brackets

FM200 Distribution components:

• Discharge nozzles
• Piping for cylinder and nozzles

Slave components:

• Pneumatic valve actuators
• Actuation check valve
• Vent check
• Actuation hose
• Fitting for cylinder (salve arrangement)

Trim components:

• Pressure gauge
• Connection fittings
• Low-pressure supervisory switch
• Electric valve actuator
• Manual valve actuator

Supplemental components:

• Discharge pressure switch
• Manifold check valve
• Complete equipment for multi-cylinder configuration
• Control Panel : It monitor the condition of all connected devices like electric actuator, detectors, warning device, cylinder pressure, manual release and abort stations
• Optional : VESDA System with control panel

Advantages of an FM200 – Fire suppression system:

• It react very fast on electrical, flammable liquid fire and suppress fire from infrastructure
• It save infrastructure from major damage by fire result in lower repair cost
• Refilling of HFC227ea – FM200 is simple and cost effective
• Depending upon size of infrastructure, FM200 occupy less space on given infrastructure
• Compare to other suppression system, FM200 is environment friendly and does not affect stratospheric ozone layer
• FM200 leaves no residue and safe to use for occupied safe
• FM200 suppression system is accepted by worldwide including developed and developing nations

Product Details:

Fire Projects has expertise in SITC of NOVEC 1230-Fire Suppression System with its component. Fire suppression here it called as NOVEC gas suppression systems are commonly used in:

• DATA Centres
• Comms Rooms
• Telecommunication facilities
• UPS Rooms
• Medical facilities

Descriptions:

• When fire breaks out in server rooms, data-centers, museums and other sensitive environments, sometimes the solution can be as damaging as the fire
• Novec™ 1230 is a unique fire extinguishing clean agent
• Among the Clean Agents, it has the lowest atmospheric lifetime of 5 days
•  It is stored as a liquid, which makes it easier for transport, and also has zero ozone depletion potential
• As with other clean agents, it is an excellent choice for computer rooms, electrical control rooms, storage areas and any high value area
• Fire Projects products save people and property from the dangers of fire
• Our expertise into NOVEC offering and designing
• Fire Projects is the smart choice when early fire detection and suppression needs are especially demanding
• Fire Projects will enhance customer focus and partnerships, provide highly efficient service and training, preserve a deep combined expertise in an array of vertical markets, and accelerate our product and technology implementation, to the advantage of everyone who benefits from a world made safer from fire
• Fire Projects offer Clean Agent Suppression System with Novec 1230 uses a unique approach to deliver the agent to the hazard area
• By using an external Nitrogen (N2) source to drive the Novec
• Utilizing super-pressurized Novec fluid propelled by one or two external Nitrogen drivers, Novec system easily achieves bestin-class performance in every category where it matters
• Nozzles supplied by Fire Projects maximize pressure utilization and are able to cover sub-floors of up to 42.5’ x 42.5’ (12.95m x 12.95m) with a single nozzle
• Improved agent vaporization allows nozzles to be mounted 18.5’ (5.64m) above the floor deck thereby enabling tall rooms to be protected by a single level of nozzles
• Fire Projects offer Clean Agent Suppression System with Novec 1230 uses a unique approach to deliver the agent to the hazard area
• By using an external Nitrogen (N2) source to drive the Novec
• Utilizing super-pressurized Novec fluid propelled by one or two external Nitrogen drivers, Novec system easily achieves bestin-class performance in every category where it matters
• Select Fire Projects for new implementation of NOVEC 1230 fire suppression system is most effective way for small to medium size datacenter, UPS room, medical facilities and telecommunication facilities
• We support our clients from Designing up to Commissioning up to AMC
• We also provide AMC–Annual Maintenance Contracts for all types of Fire & security Systems

Advantages of an NOVEC 1230 – Fire suppression system:

• Pipe length from storage to protected area
• Discharge nozzle coverage area and
• Discharge nozzle height from floor.
• Extra Nitrogen Gives You More Coverage While Reducing Installation Costs
• Centrally-Located Cylinder Banks
• Increased agent flow rates and distances provide better coverage for larger hazard areas

Product Details:

We are indulged in offering the finest quality Fire Suppression System.

Features:

• Safe for personnel and equipment
• Leaves no residue behind
• Most systems are designed to extinguish fires within one minute.
• Environmentally friendly
• Actuation by solenoid or manual actuator
• Three available high-pressure (2900 PSI [200 bar]) cylinder sizes
• Stored as a gas within the cylinder assembly
• FM Approved
• ULC Listed

Other details:

• With the big push toward "Green", Fire Projects recommend inert gasses which have become a good choice as they are the most green of all of the Clean Agents
• Inert gasses are defined as using one or more of the gasses Nitrogen, argon, or helium
• CO2 is also found in one of the inert gas blends. Inert gasses work by removing the oxygen in the hazard to a point where it will not support a fire, but still high enough to support life
• Design considerations when using inert gasses are pressure venting and volume
• It is critical to design the system to achieve the correct concentration, and not remove too much oxygen in the room
• Plus, venting of inert gasses is important as it displaces the air volume in the hazard area
• Fire Projects can assist in determining which agent is best suited to protect the hazard area (includes detection and control for the system)
• The air we breathe has approximately 21% of Oxygen
• Oxygen is the key factor in sustaining a fire and the key factor in keep us alive too
• By removing the oxygen, we will certainly extinguish a fire, but that comes with obvious problems
• How do we sustain life at the same time
• Fires need more than 15% Oxygen to combust
• Anything below this level of oxygen will not be enough for a fire to sustain combustion
• Luckily, we only need 12% plus of oxygen to survive and this is where the answer lies
• To extinguish a fire and sustain life, we need to reduce oxygen from 21% (assuming were at sea level) to below 15%, but not less than 12%
• This will extinguish a fire and sustain life at the same time

Inert Gas Fire Suppression systems are commonly found with the following blends and names:-

• Inergen fire suppression - IG541
• Argon/nitrogen fire suppression - IG55

Inergen fire suppression - IG541:

• Inergen fire suppression agent is made up of 50% Argon, 42% Nitrogen and 8% Co2
• The Co2 in this blend helps us absorb oxygen into your blood cells
• By doing this it decreases the risk of the symptoms described above
• Co2 is also known to increase our heart beat rate and also induce hyper ventilation
• This gas clearly suggests an advantage over the other inert gas fire suppression systems, but there is a down side to this
• If the protected space is filled with toxic bi-products of combustion, the hyper ventilating will introduce more toxins and increase the risk of other side effects

Argon/nitrogen fire suppression - Commonly known as IG55 fire suppression:

• IG55 fire suppression is a balanced mix of 50% Argon & 50% Nitrogen
• The fire suppression agent provides good buoyancy, which keeps it in the protected space for longer, thus optimising the suppression period
• Select Fire Projects for new implementation of Inert fire suppression system is most effective way for small to medium size datacenter, UPS room, medical facilities and telecommunication facilities
• We support our clients from Designing up to Commissioning up to AMC

Product Details:

FK 1230 (FK-5-1-12) Clean agent system also known as NOVEC 1230 are employed to protect critical installations formerly protected by Halon 1301.

• Data Processing Centers
• Telephone Switches
• Process Control Rooms
• Art and Historical Collections
• Archive & Museums
• Marine, Oil & Gas
• Aerospace, Aviation & Military

FK 1230 (FK-5-1-12) agent compiles with NFPA Standard 2001 : Standard for Clean Agent fire Extinguishing systems, EPA SNAP Program (Significant New Alternate Policy)

Additional Information:

• Item Code: H2-120-000
• Production Capacity: 34 / 80 / 120 / 140 LTR
• Delivery Time: NORMAL CONDITION 5 TO 7 WEEK
• Packaging Details: WOODEN PACKAGE

Product Details:

Being one of the trusted organizations in the market, we are indulged in providing a wide range of Fire Suppression System Services.

Fire Projects provides complete Fire Suppression system services, including sales, installation, inspection, recharge, testing, and more. Fire Projects provide the inspection and maintenance schedule to keep your system in compliance, as well as keep accurate inspection and maintenance records that are required by officials. We provide immediate response to fire suppression system discharges, whether accidental or from a fire, to get your system back into service as quickly as possible.

Fire Suppression services include:

• Testing and cleaning all detectors
• Verifying shutdown and evacuation circuits
• Verifying cylinder pressures and weights
• Checking for changes in hazard integrity
• Checking input and output circuit supervision
• Simulating system discharge and testing releasing circuits
• Visually inspecting agent piping and nozzles
• Checking hydro test dates for cylinders and discharge hoses

Cylinder/valve assemblies must be handled, installed, inspected and serviced only by qualified and trained personnel in accordance with the instructions contained in this manual, the cylinder nameplate, NFPA-2001, and any other regulations and codes that may apply. Before performing maintenance or refilling procedures refer to the material safety data sheets in the appendix at the back of this manual. A regular program of systematic maintenance must be established for continuous, proper operation of all FM-200, NOVEC 1230 and INERT units, and to avoid violating the warranty. A periodic maintenance schedule must be followed and an inspection log maintained for ready reference.

As a minimum, the log must record:

• Inspection interval
• Inspection procedure performed
• Maintenance performed